5069-L320ER Allen Bradley Rockwell CompactLogix Controller

Product parameters

Controller type: CompactLogix 5380 standard controller (no safety functions, no motion control)

Memory:

User memory: 2 MB

Non-volatile storage: 2GB (standard 1784-SD2 SD card), supports expansion to:

1 GB (1784-SD1)

8 GB (1784-SDHC8)

32 GB (1784-SDHC32)

4 GB (9509-CMSDCD4 CodeMeter CmCard)

Task support:

Maximum number of tasks: 32 (standard tasks)

Number of programs per task: up to 1000

Communication interface:

2 Ethernet /IP ports (supporting 10 Mbps, 100 Mbps, 1 Gbps, full-duplex)

One USB 2.0 port (for programming and configuration, 12 Mbps)

Network support

Maximum Ethernet /IP node: 40

Maximum socket interface: 32

Supported network topologies: Linear, Star, Device-level Loop (DLR)

Ethernet mode: Dual IP mode (independent IP address per port) or linear /DLR mode (shared IP address)

I/O support:

Maximum local I/O modules: 16 (Compatible with Allen-Bradley 5069 Compact I/O modules)

Distributed I/O: Access the Ethernet /IP network via 5069-AEN2TR or 5069-AENTR

I/O capacity: 128,000 data packets per second

Power supply:

Module Power supply (MOD Power) : 18-32 V DC (SELV/PELV), maximum current 475 mA, surge current 850 mA (lasting for 125 ms)

Maximum power supply current: 9.55A (DC)

Sensor/Actuator (SA) power supply:

Voltage range: 0-32 V DC or 0-240 V AC (47-63 Hz, ATEX/IECEx maximum 125 V AC)

Maximum current: 9.975A (AC), 9.95A (DC)

On-site power supply current: 25 mA (AC), 10 mA (DC)

Power consumption:

Maximum power consumption: 8.5 W

Maximum heat dissipation: 29 BTU/hr

Installation:

DIN rail installation (Recommended zinc-chrome-plated steel EN50022 rail, 35 x 7.5mm, only supports horizontal installation)

Grounding requirements: A DIN rail with good electrical conductivity is required to ensure reliable grounding

Environmental conditions:

Operating temperature: 0°C to 60°C (32°F to 140°F)

Storage temperature: -40°C to 85°C (-40°F to 185°F)

Relative humidity: 5% to 95% (no condensation)

Vibration: 5 g (10-500 Hz)

Impact: 30 g during operation (3 pulses, 11 ms), 50 g during non-operation

Enclosure: Open type (needs to be installed in a cabinet with an appropriate protection level, dust-proof and resistant to corrosive gases)

Programming language: Supports IEC-61131-3 standard, including ladder Diagram (LD), Function Block Diagram (FBD), Structured Text (ST), and Sequential Function Diagram (SFC).

Certification:

Comply with EMC standards (EN 50081-2, EN 50082-2)

Type test: 50 V or 300 V isolation voltage (depending on the insulation type)

Function

High-performance task processing

Supports up to 32 standard tasks, with each task capable of containing 1000 programs, making it suitable for complex control logic.

It provides 2 MB of user memory to meet the storage requirements of small and medium-sized automated applications.

Flexible network connection

The dual Ethernet /IP ports support 10/100 Mbps and 1 Gbps full-duplex communication, and support linear, star and DLR topologies, providing network redundancy and fault tolerance.

Supports up to 40 Ethernet /IP nodes and 32 socket interfaces, suitable for distributed control systems.

The USB 2.0 port is used for programming, configuration and debugging, and the communication rate reaches 12 Mbps.

Modular I/O expansion

Supports up to 16 local I/O modules (5069 Compact I/O), and distributed I/O can be expanded through 5069-AEN2TR or 5069-AENTR.

The I/O capacity reaches 128,000 data packets per second, supporting high-throughput data processing.

Programming and Configuration

Programming is carried out using Studio 5000 Logix Designer software (version 31 or higher), supporting ladder diagram (LD), Function Block Diagram (FBD), Structured text (ST), and Sequential Function Diagram (SFC).

Support all event triggering to ensure flexible task scheduling.

Reliability and environmental adaptability:

The open shell design requires installation in a protective cabinet to adapt to industrial environments (dust-proof and resistant to corrosive gases).

Supports DIN rail installation. It is recommended to use zinc-chrome-plated steel rails with good electrical conductivity to ensure grounding reliability.

Withstand vibration (5 g) and shock (30 g during operation and 50 g during non-operation).

Diagnosis and Monitoring

Provide a status indicator to display the operating status of the controller in real time.

It supports fault reporting, module suppression and electronic key functions, facilitating system diagnosis and maintenance.

Application scenarios

Manufacturing Automation

It is used to control production lines, assembly lines and packaging equipment, and handle standard control tasks (such as sensor and actuator management).

Suitable for small and medium-sized factories, it meets the requirements of limited I/O points and moderate complexity control.

Material handling

It is applied to conveyor belts, automated warehousing and sorting systems, supporting high-performance task processing and real-time data transmission.

Dual Ethernet ports and DLR topology ensure network reliability, making it suitable for dynamic material handling scenarios.

Distributed control system

Distributed I/O control is achieved through Ethernet /IP networks, which is suitable for factory workshops or cross-regional equipment management.

When used in conjunction with the 5069-AEN2TR or 5069-AENTR adapter, it provides flexible remote I/O expansion.

Energy and Public Utilities

In water treatment, power distribution or renewable energy systems, control equipment such as pumps and valves.

It can adapt to harsh environments (such as high temperatures and vibrations) and is suitable for outdoor or industrial site applications.

OEM equipment integration

Provide compact and high-performance control solutions for original equipment manufacturers (Oems), integrated into custom machinery or systems.

Supports multiple programming languages to simplify device development and debugging.

General Industrial Control

It is applicable to HVAC systems, pump station control or other general automation tasks, and supports direct communication with SCADA and HMI systems.

2 MB of memory and 40 Ethernet /IP nodes support a medium-sized control network.

Advantage Products:

All items are Distributor Ready-stock Genuine Brand-new Supplying, please inform us if the other conditions are needed, Used, Open-box, Refurbished, etc.

Many Available just wait for you, feel free to ask to get better deal!!!

Bou L(Sales Manager)            

Tel:+86-175 5077 6091                                                                                              

E-mail:[email protected]       

Tina(Sales Specialist)       

Tel:+86-131 2336 8748                                                                                                            

E-mail:[email protected]     

Ricardo(Sales Specialist)       

Tel:+86 18359251915                                                                                                      

E-mail:[email protected]

Doris(Sales Specialist)       

Tel:+86 13599531915                                                                                                      

E-mail:[email protected]