HUAWEI CR5D00E8GF72 FLEXIBLE CARD

Component Code :03033LBK

Model :CR5D00E8GF72

Single board category: Flexible card insertion

Silk-screen printing :P53-8xGE-8xSTM4c PO-SFP

Typical power consumption [W]:46 W

Typical heat dissipation value [BTU/hour]:149.24 BTU/hour

Long-term operating environment temperature [°C]:0°C to 45°C

Short-term operating environment temperature [°C]:-5°C to +55°C

Basic functions:

This single board supports 8 GE/10GE+8 622M POS, or 8 GE/10GE+8 155M POS, or 8 GE/10GE+4 2.5G POS, or 8 GE/10GE+1 10G POS. The default POS port is 622M POS. Other modes can be switched through the command line set service-mode card-bandwidth-mode. The ETH port supports GE/10GE adaptive. The default port is GE enabled, supporting line-speed forwarding of 8 GE ports. To enable other port functions, it needs to be used in conjunction with the corresponding RTU.

When the flexible card insertion mother board is used in conjunction with sub-cards, each flexible card insertion mother board has 2 physical sub-card slots (0 and 1), and can be virtually expanded to 4 card slots (0/1/2/3). When the sub-card is inserted into the physical slot 0, the virtual slot 0 generates the ETH sub-card, and the virtual slot 2 generates the POS sub-card. When the sub-card is inserted into physical slot 1, virtual slot 1 generates an ETH sub-card, and virtual slot 3 generates a POS sub-card. The operation interface shows that the card number is consistent with the virtual card slot number.

3. Virtual cards are divided into master and slave cards. The virtual card slot is the same as the physical slot. The corresponding child card is the master card, and the rest are slave cards. Support powering on and off the master card in the virtual sub-card. Powering on and off the master card will affect the slave card (a prompt will be given when the specific slot command line is issued), and the slave card does not support powering on and off. The virtual sub-card slot supports independent reset. The reset of the entire card needs to be accomplished by powering on and off. Only the virtual master card can query the corresponding temperature and voltage information.

Reliability and availability: Supports hot plugging

Restrictions and Instructions:

It needs to be used in conjunction with an RTU. On the LPUF53 single board, only ports 0-5 support 10GE bandwidth capability, and the license activation port 10G bandwidth is supported. Ports 6-7 do not support 10G license and do not support switching to 10G bandwidth.

2. Each Ethernet port group has 4 ports 0-3 and 4-7. Within each port group, 10GE LAN or 10GE WAN can be switched on a group basis. The combination of 10GE LAN and 10GE WAN is not supported. When a 10GE port operates in WAN mode, it can only be used in Master mode and does not support Slave mode.

3. The 10G/2.5G/622M/155M POS ports cannot be used interchangeably. Ports 0, 2, 4 and 6 support Slave mode.

4. 2.5G POS supports 4 ports, and 10G POS supports 1 port.

5. When using the electrical port module, there may be interference between the network cable of the electrical port module and the sub-card wrench near the sub-card wrench. It is recommended that the electrical port module only be used for even ports such as 0, 2, 4, and 6.

Whether hashing is supported: No

Whether port rate adaptation is supported: GE/10GE adaptation is supported.

Whether FlexE is supported: No

Does it support MACsec? No

Does it support the use of RTU? Yes

High-speed card

Port 0-7: GE mode is not controlled, while 10GE mode is controlled at 100M.

POS card

Ports 0 to 7 are controlled for 5 meters.

If you want to use the bandwidth of other ports, you need to load the RTU.

Advantage Products:

All items are Distributor Ready-stock Genuine Brand-new Supplying, please inform us if the other conditions are needed, Used, Open-box, Refurbished, etc.

Many Available just wait for you, feel free to ask to get better deal!!!

Bou L(Sales Manager)            

Tel:+86-175 5077 6091                                                                                              

E-mail:[email protected]       

Tina(Sales Specialist)       

Tel:+86-131 2336 8748                                                                                                            

E-mail:[email protected]     

Ricardo(Sales Specialist)       

Tel:+86 18359251915                                                                                                      

E-mail:[email protected]

Doris(Sales Specialist)       

Tel:+86 13599531915                                                                                                      

E-mail:[email protected]